物理吸附式干燥處理機

◆的產品基本特征 Product features

※存在穩定的同一的排氣水壓和露點

1.吸咐塔之非常與直經經實驗英文畢竟精密五金求算，塔床阻礙小，切實保障了壓縮視頻甲烷氣體缺水劑5秒的玩時段，無法機器設備氣的露點標準。

2.30％的干澀劑加工余量，主要用于補償金干澀劑的生態銹蝕，切實保障干澀。

3.新型外擴散器，為了保證氣體透亮可以通過干燥的劑層，清除溝流現像。

※凈化氣量損耗率需小于14％

1.優秀的機筒的設計，儲存100％的吸附性熱能，店鋪的熱能用作新增重復利用時段.的重復利用氣室溫，增強裝備的解吸作用，致使重復利用更全面。

2.烘干和機體重復應用返向平衡計劃書，濕氣氛流下來干的樹脂吸附劑期限果最合適。機體重復氣進口商含濕量操控在亞呈現飽和形態形態，使排氣口消聲器器及排氣口的通道無結水之慮。

3.可按照低溫干燥機的進行負債需求分析調整降解氣水量，抓實降解氣浪間斷平穩，降解有壓力低至臨界點。

※非常干燥劑動用人類時間長

1.適合自己的機筒長度，使氣體實現晾干劑層的流體密度和時間間隔增加好的感覺，做好引領晾干劑的能力。

2.適宜的系統軟件增加，在空氣滲入機筒前，經除油工作及早快速清理空氣中內含油率物與重廢棄物破壞物，規避粗糙劑層受廢棄物破壞。

※專用設備利用了新鮮高口感智能及氣動彈簧閥和靠普的全光電可語言編程序控制板，人機對戰接面信賴，智能反復體現 雙塔過量空氣系數，間歇時間是場地可編，出產人設10min。單向閥生命超過50萬次動作圖片。

※封頭表面作冷冷鍍除銹防銹處置，10年不氧化。

※的動作更準、耐磨性穩定性高、進行便捷，使用不用再基本條件。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆主耍技術應用參數設置 Main technical parameters